How To Make DMT DMT stands for N,N-dimethyltryptamine. It is a semisynthetic compound similar to psilocin(the hallucinogenic substance in psilocybin) ins structure. The most common method of ingestion is smoking. Soaked parsley leaves are the usual method of ingestion although persons have dipped marijuana in it and said the experience was fantastic. The following recipe can be performed in the kitchen. Recipe for DMT: 1. Mix thoroughly and dissolve 25 grams of indole with a pound of dry ethyl ether in a 2000 ml flask(2 quart jar.) 2. Take an ice tray and fill with chipped or shaved ice. Cool solution for about 35 minutes until it reaches 0 degrees C. At the same time cool 50 ml dry oxalychloride to about 5 degrees below 0 C. in the same ice tray. 3. VERY slowly add the oxalychloride solution to the indole solution. These two chemicals are highly reactive. Avoid boiling over, contact with skin, and fumes. 4. Wait until all the bubbling has died down, then add a few handfuls of table salt to the ice tray, to cool the solution further. Label the solution "solution 1" and put it in the freezer. 5. Cool 100 ml. of dry ethyl ether in a 500 ml. flask to 0 degrees C. in a salted ice tray. At the same time cool an unopened bottle of dimethylamine to 0 degrees C. in the same ice bath. 6. Open the seal of the dimethylamine bottle and slowly pour a steady stream into the ether. Label "solution 2." 7. Very slowly and carefully add solution "1" and "2" together. 8. Now take the mixed solutions from the ice tray and bring up to room temperature stirring the solution all the time. You should be left with a solution that is almost clear. If it is still murky, continue stirring until it becomes as clear as possible. 9. Now filter the solution to seperate the precipitate by suction. <---Solution and Precipitate ------------ \ /<---Funnel / / <-- Rubber hose to \ / and / / Vacuum source \ / Filter/____/ \*****\ /*************{ }*****/ <--- Two hole \****{ }*************{ }****/ rubber stopper \ { } { } <-/--- Glass Tube \ { } { } / | { } { } | | | | | | | | | |__________________________| Figure A. 10. Refilter with suction after pouring technical ether over the precipitate. 11. Repeat filtering once more with ether, then twice with water. 12. Let this substance dry on a plastic or china plate.(do not use metal) After drying, a solid material will be formed. Take particles and place them in an 800 ml beaker. 13. Mix 100 ml. benzene with 100 ml. methyl alcohol. After this mixture has been stirred, cover solid particles from step 12 with about 1/2 inch of the solution and heat the beaker in water until all solid material had dissolved. Add more solvent if necessary.(Note: Do not place beaker in water bath directly over the flame.) 14. After all solid material has dissolved, remove beaker from the heat, and allow to cool. As it cools, small needle-shaped crystals will appear. When this happens, try to pour off as much solvent as possible without disturbing the crystals. 15. Place crystals in a 1000 ml flask and dissolve in tetrahydrofurane.(Use only as much as absolutely necessary.) Label this solution "A". 16. Slowly mix 200 ml. tetrahydrofurane and 20 grams lithium aluminum hydride in a 500 ml flask, and label it solution "B". (By the way, lithuim aluminum hydride ignites on contact with moisture. Protect eyes and hands.) 17. Mix solutions "A" and "B" slowly, stirring constantly. 18. Prepare a water bath and heat solution for three hours, stirring for four minutes every half hour. When not stirring, make sure to use aspirator tube. / / <--- Rubber Tubing --- \**{ }**/<---- One hole rubber stopper /**{ }**\ and glass tubing / { } \ / { } \ : : : : : : \ ~~~~~~~~~~~~~~~:_____________:~/ \______________________________/ Heat source Figure B. Place Figure B. flask at a higher level than Figure A. flask. Run tube from Figure B. flask down to left side of figure A. flask, replacing funnel with glass tubing. Disconnect right side tube from vacuum source. This will be used as the aspirator tube. 19. When this is completed, allow the flask to remain at room temperature for about 20 minutes. Then place in salted ice bath, and cool to 0 degrees C. Add a small amount of chilled methanol, stirring gently until solution appears murky. 20. Filter this murky solution through a paper filter in a funnel, and collect the filtered liquid in a flask. 21. Add 100 ml. of tetrahydrofuran through the filter and collect in the same flask. Now heat the solution in a water bath until most of the tetrahydrofuran is evaporated and a gooey substance remains. 22. Place little piles of this substance on a cookie tray and dry with a heat lamp for three or four hours. Well, after all that you now have DMT. Was it worth it? To ingest, crumble a small quantity with parsley or mint, and smoke. Do not inject. Do not mix with tobacco. Keep your thoughts free and your reality...err different. - Black Adder Call Spatula City (707) 451-2835. Amiga 14.4 HST. [0;1m